e e - - p p h h e e m m t t m m m m i i c c a a e e 3 3 1 1 4 4 (preliminary) ? tel : 82-31-250-5011 ? all specifications may change without notice. ? rfsales@rfhic.com ? version 0.3 0 b product features 1 b application ? low noise figure ? higher gain ? higher linearity ? sot89 smd type package ? higher productivity ? lower manufacturing cost ? -64dbc cso 135 channels @ +20dbmv/ch ? -74dbc ctb 135 channels @ +20dbmv/ch ? -82dbc xmd 135 channels @ +20dbmv/ch ? pb-free/rohs compliant ? low noise amplifier for catv, satellite ? cable modem ? ftth (g-pon, ge-pon) ? optical node 2 b description AE314 is designed as low cost driv e amplifiers for many applicati ons including ftth, catv system. this mmic is based on gallium arsenide enhancement mode phemt which shows low current draw and very low noise. the data in this spec sheet is valid only for 75 ohm application. 3 b specifications (50mhz~2200mhz) 4 b parameter unit min typ max condition frequency mhz 50 ~ 2200 gain db 21.3 19.2 at 500mhz at 2000mhz gain flatness 2.5 input return loss db -8 -4.3 output return loss db -8 -3.5 output ip3 dbm 33 36 at 1000mhz/+10dbm 2tone 1db compression point dbm 19 22 at 1000mhz noise figure db 2 3 cso dbc -64 135 channel, +20dbmv/ch ctb dbc -74 135 channel, +20dbmv/ch xmod 30 ~ 870mhz dbc -82 135 channel, +20dbmv/ch dc current ma 100 vdd = 5.0v absolute minimum and maximum ratings 5 b parameter unit min typ max device voltage vdc +5 +5.5 operating temperature -40 +85 storage temperature -40 +150 note 1. test conditions unless otherwise noted. ta=25 , vdd=+5v, 75 ? system 2. oip3 measured with 2 tones at an output power of +10dbm/tone separated by 1mhz, test freq = 1000mhz package : sot-89
e e - - p p h h e e m m t t m m m m i i c c a a e e 3 3 1 1 4 4 (preliminary) ? tel : 82-31-250-5011 ? all specifications may change without notice. ? rfsales@rfhic.com ? version 0.3 application circuit: 50mhz ~ 2200mhz, 75ohm system typical rf performance: v dd =5v, i ds =100ma, ta=25 , 75ohm system 0.5 1.0 1.5 2.0 0.0 2.5 -10 0 10 20 -20 30 -20 -10 0 10 -30 20 fre q , ghz return loss(db) gain(db) s-parameter multi-tone test 135ch_flat@output power +20dbmv/ch level: +20dbmv tilt: 135ch_flat frq xmd(ncta) ctb_raw ctb_cor n-flr csu_raw csu_cor csu_frq csl_raw csl_cor csl_frq 55.25 89.3 77.6 81.9 77.8 77.2 81.5 55.99 64 64.2 53.99 77.25 91.8 77.8 82.1 78.2 64.9 65.1 78 77.6 82 76.61 109.25 89.3 77.3 81.7 77.8 77.2 81.5 110.44 64.6 64.8 107.99 211.25 88.7 76.7 81.1 77.3 74.9 79.3 212.5 65.3 65.6 209.99 331.25 86.8 76.2 80.5 76.9 72.9 75.5 332.5 65.5 65.9 329.99 445.25 85.9 76.8 81.2 77.1 71.9 73.4 446.49 66.5 66.8 443.99 547.25 86.1 75.9 80.2 76.1 69.9 71 548.5 66.7 67.3 545.99 637.25 84.3 76 80.3 76.4 69.8 70.9 638.49 69.8 70.9 635.99 745.25 83.2 75.9 80.2 76.2 67.7 68.4 746.49 73.1 76.1 743.99 859.25 82.1 74.8 79.1 75.3 67 67.7 860.49 74.2 78.6 858.49 min 82.1 74.8 79.1 75.3 64.9 65.1 55.99 64 64.2 53.99 max 91.8 77.8 82.1 78.2 77.2 81.5 860.49 77.6 82 858.49 s21 s22 s11 noise figure vs frequency 0 1 2 3 4 5 0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 freq(mhz) nf(db)
e e - - p p h h e e m m t t m m m m i i c c a a e e 3 3 1 1 4 4 (preliminary) ? tel : 82-31-250-5011 ? all specifications may change without notice. ? rfsales@rfhic.com ? version 0.3 6b specifications (50mhz~1000mhz) 7 b parameter unit min typ max condition frequency mhz 50 ~ 1000 gain db 20 22 input return loss db -17 output return loss db -16 output ip3 dbm 35 38 at 500mhz/+5dbm 2tone 1db compression point dbm 18 21 at 500mhz noise figure db 2 3 cso dbc -53 -49 135 channel, +30dbmv/ch ctb dbc -63 -58 135 channel, +30dbmv/ch xmod 30 ~ 870mhz dbc -63 -58 135 channel, +30dbmv/ch dc current ma 100 vdd = 5.0v application circuit: 50mhz ~ 1000mhz, 75ohm system +5v output 470nh 10 nf 100 nf 4.7 uf (tantal) input ae 314 1 pf 8. 2 nh 0. 5 pf 5 pf 10 nf 10 nh 470 ohm 680 ohm 0 ohm 0. 75 pf note 1. test conditions unless otherwise not ed. test freq = 500mhz, ta=25 , vdd= +5v, 75 ? system 2. oip3 measured with 2 tones at an output power of +5dbm/tone separated by 1mhz, test freq = 500mhz
e e - - p p h h e e m m t t m m m m i i c c a a e e 3 3 1 1 4 4 (preliminary) ? tel : 82-31-250-5011 ? all specifications may change without notice. ? rfsales@rfhic.com ? version 0.3 typical rf performance: v dd =5v, i ds =100ma, ta=25 , 75ohm system 0.20.40.60.81.0 0.0 1.2 5 10 15 20 0 25 -20 -10 0 10 -30 20 freq(ghz) gain(db) return loss(db) s-parameter multi-tone test 135ch_flat@output power +30dbmv/ch level: +30dbmv tilt: 135ch_flat frq xmd(ncta) ctb_raw ctb_cor n-flr csu_raw csu_cor csu_frq csl_raw csl_cor csl_frq 55.25 68.6 73.5 76.1 76.9 75.9 80.3 55.99 54.8 54.8 53.99 77.25 68.9 74.1 77.1 77 54.8 54.8 77.99 76.6 80.9 76.18 109.25 68.7 72.5 74.4 77.2 74.1 77.1 109.99 54.7 54.7 107.99 211.25 67.5 72 73.6 77 70.9 72 212.5 53.9 53.9 209.99 331.25 66.7 70.7 72.1 76 66.3 66.8 332.5 55 55 329.99 445.25 65.8 69.8 70.8 76.7 65.1 65.4 446.49 56.1 56.1 443.98 547.25 66.3 69.6 71.2 74.6 62.8 63.1 548.5 57.7 57.7 545.98 637.25 65.4 68.6 69.6 75.3 62.1 62.3 638.49 60.6 60.8 635.98 745.25 64.8 68.2 69.3 74.8 60.6 60.8 746.49 65.1 65.6 743.99 859.25 64 67.1 68.6 72.7 58.3 58.4 860.49 70.2 73.8 858.49 min 64 67.1 68.6 72.7 54.8 54.8 55.99 53.9 53.9 53.99 max 68.9 74.1 77.1 77.2 75.9 80.3 860.49 76.6 80.9 858.49 s21 s22 s11 noise figure vs frequency 0 1 2 3 4 5 10 200 400 600 800 1000 freq(mhz) nf(db)
e e - - p p h h e e m m t t m m m m i i c c a a e e 3 3 1 1 4 4 (preliminary) ? tel : 82-31-250-5011 ? all specifications may change without notice. ? rfsales@rfhic.com ? version 0.3 8b specifications (50mhz~1000m hz, bias control) 9 b parameter unit min typ max condition frequency mhz 50 ~ 1000 gain db 20 22 input return loss db -17 output return loss db -16 output ip3 dbm 35 38 at 500mhz/+5dbm 2tone 1db compression point dbm 18 21 at 500mhz noise figure db 2.5 3.5 cso dbc -60 -55 135 channel, +30dbmv/ch ctb dbc -67 -62 135 channel, +30dbmv/ch xmod 30 ~ 870mhz dbc -64 -59 135 channel, +30dbmv/ch dc current ma 130 vdd = 5.0v application circuit: 50mhz ~ 1000m hz, 75ohm system, bias control note 1. test conditions unless otherwise not ed. test freq = 500mhz, ta=25 , vdd= +5v, 75 ? system 2. oip3 measured with 2 tones at an output power of +5dbm/tone separated by 1mhz, test freq = 500mhz
e e - - p p h h e e m m t t m m m m i i c c a a e e 3 3 1 1 4 4 (preliminary) ? tel : 82-31-250-5011 ? all specifications may change without notice. ? rfsales@rfhic.com ? version 0.3 typical rf performance: v dd =5v, i ds =130ma, ta=25 , 75ohm system 0.20.40.60.81.0 0.0 1.2 5 10 15 20 0 25 -20 -10 0 10 -30 20 freq(ghz) gain(db) return loss(db) s-parameter multi-tone test 135ch_flat@output power +30dbmv/ch level: +30dbmv tilt: 135ch_flat frq xmd(ncta) ctb_raw ctb_cor n-flr csu_raw csu_cor csu_frq csl_raw csl_cor csl_frq 55.25 71.5 74.6 79 75.8 75.7 80 55.98 62.3 62.5 53.99 77.25 75 75.2 79.5 75.9 62.6 62.8 77.99 75.6 80 76.03 109.25 73.6 75.1 79.4 76.4 75.8 80.2 109.99 62.1 62.2 107.99 211.25 73.9 75.1 79.4 76.4 72.1 74 212.5 61.8 62 209.99 331.25 73.2 73.7 78.1 75 68.6 69.7 332.49 61.9 62.1 329.99 445.25 72.4 74.2 78.5 75.9 67.1 67.7 446.49 62.6 62.8 443.99 547.25 72.8 72.9 77.2 73.6 63.9 64.4 548.49 63.6 64 545.99 637.25 72.2 72.9 77.2 74.2 63.7 64.2 638.49 66.3 67 635.99 745.25 71.4 72.1 76.5 73.8 62.4 62.7 746.49 69.8 72 743.99 859.25 70.9 70.7 75.1 71.7 60.8 61.1 860.5 70.7 75 858.49 min 70.9 70.7 75.1 71.7 60.8 61.1 55.98 61.8 62 53.99 max 75 75.2 79.5 76.4 75.8 80.2 860.5 75.6 80 858.49 s21 s22 s11 noise figure vs frequency 0 1 2 3 4 5 10 200 400 600 800 1000 freq(mhz) nf(db)
e e - - p p h h e e m m t t m m m m i i c c a a e e 3 3 1 1 4 4 (preliminary) ? tel : 82-31-250-5011 ? all specifications may change without notice. ? rfsales@rfhic.com ? version 0.3 for a safe use in all situations, it is recommended to have proper esd control techniques while the device is being handled. he re are some recommended precautions; - person at a workbench should be earthed via a wrist strap and a resistor. - all mains-powered equipment should be connected to the mains via an earth-leakage switch. - equipment cases should be grounded. - relative humidity should be ma intained between 40% and 50%. - an ionizer is recommended. - keep static materials, such as plastic envelope s and plastic trays etc. away from the workbench 1 2 b pcb pad layout recommended mounting configuration 1 0 b esd protection 1 1 b dimensions pin no function 1 input 2 ground 3 output/bias 4 ground mounting configuration notes 1.ground / thermal via holes are critical for the proper performance of this device. 2. add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. mounting screws can be added near the part to fasten the board to a heatsink. ensure that the ground / thermal via hole regi on contacts the heatsink. 4. do not put solder mask on the backside of the p cb in the region where the board contacts the heatsink. 5. rf trace width depends upon th e pcb material and construction. 6. use 1 oz. copper minimum. 7. all dimensions are in millimeters. rfhic corporation (rfhic) reserves the right to make changes to any products herein or to discontinue any product at any time w ithout notice. rfhic do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, inclu ding without limitation consequential or incidental damages. the product specifications herein expressed ha ve been carefully checked and are assumed to be reliable. how ever, rfhic disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase or ders. rfhic products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold rfhic and its directors, officers, stockholders, employees, representatives and distributors harmless ag ainst any and all claims arising out of such use. rfhic?s liability under or arisin g out of damages, claims of whatsoever kind and nature which rfhic p roducts could cause shall be limited in amount to the net p urchase p rice of the p roducts sold to bu y er b y rfhic .
|
